4.0inch Arduino Display-Mega2560 NT35510

Product Picture

Name	Parameter
Display Color	RGB 65K color
SKU	MAR4018
Screen Size	4.0(inch)
Type	TFT
Driver IC	NT35510
Resolution	800*480 (Pixel)
Module Interface	8Bit or 16Bit parallel interface
Touch Screen Type	Resistance touch screen
Touch IC	XPT2046
Active Area	86.40x51.84(mm)
Module PCB Size	58.65x108.48 (mm)
back light	8 chip HighLight white LEDs paralle
Operating Temperature	-10℃~60℃
Storage Temperature	-20℃~70℃
Operating Voltage	5V
Power Consumption	TBD
Product Weight(Package containing)	60 (g)

The blue box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows:

Solder R4 with 0Ω resistor or short circuit directly, and disconnect R5: Select 16-bit data bus mode (default),use DB0~DB15 data pin

Solder R5 with 0Ω resistor or short circuit directly, and disconnect R4: Select 8-bit data bus mode use DB0~DB7 data pin

Number	Module Pin	Pin Description	Number	Module Pin	Pin Description
1	5V	Positive power supply	2	5V	Positive power supply
3	DB8	8th bit of data bus	4	DB9	9th bit of data bus
5	DB10	10th bit of data bus	6	DB11	11th bit of data bus
7	DB12	12th bit of data bus	8	DB13	13h bit of data bus
9	DB14	14th bit of data bus	10	DB15	15th bit of data bus
11	DB7	7th bit of data bus	12	DB6	6th bit of data bus
13	DB5	5th bit of data bus	14	DB4	4th bit of data bus
15	DB3	third bit of data bus	16	DB2	2nd bit of data bus
17	DB1	1st bit of data bus	18	DB0	0 bit of data bus
19	RS	LCD register / data selection signal Low level: register, high level: command	20	WR	LCD write control signal
21	CS	LCD screen select control signal, low level enable	22	RST	LCD reset control signal, low reset
23	NC	Undefined, reserved	24	RD	LCD read control signal
25	T_IRQ	Touch screen interrupt control signal, low level when touch is detected	26	NC	Undefined, reserved
27	NC	Undefined, reserved	28	NC	Undefined, reserved
29	SD_CS	SD card select control signal, low level enable	30	NC	Undefined, reserved
31	MISO	SPI bus input signal	32	MOSI	Touch screen chip select control signal, low level enable
33	CLK	SPI bus clock signal	34	T_CS	SD card select control signal, low level enable
35	GND	Power ground	36	GND	Power ground


Arduino Mega2560 direct insertion picture

Download the Arduino test program from the Program Download column
For a description of the relevant test procedures, please refer to the test program documentation in the package

Plug the module directly into the Arduino development board ( Do not plug in?)
After the module is plugged in, power on the Arduino board

Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the colligate_test test program as an example):