2.0inch Arduino SPI Module ILI9225 SKU:MAR2001

语言选择 Languages

➤中文

➤EN

Product Picture

Product Description

• 2.0-inch color screen,support 16BIT RGB 65K color display,display rich colors
• 176x220 resolution, clear display
• Using the SPI serial bus, it only takes a few IOs to illuminate the display
• With SD card slot for convenient function expansion
• Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms
• Military-grade process standards, long-term stable work
• Provide underlying driver technical support

Product Parameters

Name	Parameter
Display Color	16BIT RGB 65K color
SKU	MAR2001
Screen Size	2.0(inch)
Type	TFT
Driver IC	ILI9225
Resolution	176*220 (Pixel)
Module Interface	4-wire SPI interface
Backlight	3 White Led
Active Area	31.68x39.60 (mm)
Module PCB Size	38.30x62.48 (mm)
Operating Temperature	-20℃~60℃
Storage Temperature	-30℃~70℃
Operating Voltage	5V/3.3V
Power Consumption	TBD
Rough Weight(Package containing)	20 (g)

Interface Definition

Number	Pin Label	Description
1	VCC	LCD Power positive (3.3V~5V)
2	GND	LCD Power ground
3	GND	LCD Power ground
4	NC	Not defined, reserved
5	NC	Not defined, reserved
6	NC	Not defined, reserved
7	CLK	LCD SPI bus clock signal
8	SDA	LCD SPI bus write data signal
9	RS	LCD register / data selection signal, high level: register, low level: data
10	RST	LCD reset signal, low level reset
11	CS	LCD chip select signal, low level enable

Connect to Arduino

Arduino UNO direct insertion picture	Arduino Mega2560 direct insertion picture

How to use on Arduino

• Step 1: Download the test program

1. Download the Arduino test program from the Program Download column
2. For a description of the relevant test procedures, please refer to the test program documentation in the package

• Step 2: Connect the Arduino development board

1. Plug the module directly into the Arduino development board ( Do not plug in?)
2. After the module is plugged in, power on the Arduino board

• Step 3: Copy the dependent library

1. Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
2. After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

• Step 4: Compile and download the program to the development board

1. Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

• Step 5: Observe the running of the program

1. After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the colligate_test test program as an example):

Program Download

• 2.0 inch Arduino SPI Module Package

Product Documentation

• 2.0 inch Arduino SPI Module User Manual
• 2.0 inch Arduino SPI Module Size Picture
• 2.0 inch TFT Specifications
• 2.0 inch Arduino SPI Module Schematic
• 2.0 inch TFT LCD Schematic and PCB Package Library
• Driver IC ILI9225 Data sheet

Reference Materials

• Arduino IDE software use illustration
• C51 Keil and stc-isp software use illustration
• STM32 keil software use illustration
• PCtoLCD2002 software use illustration
• Image2Lcd software use illustration
• Chinese and English display modulo settings

Common Software

• PCtoLCD2002
• Image2Lcd

BACK TO TOP