1.54inch SPI OLED Module SKU:MSP154X

语言选择 Languages

➤中文

➤EN

Product Picture

Product Description

• 1.54 inch OLED screen with black and white, black or blue or yellow and blue color display
• 128x64 resolution for clear display and high contrast
• Large viewing angle: greater than 160° (one screen with the largest viewing angle in the display)
• Wide voltage supply (3V~5V), compatible with 3.3V and 5V logic levels, no level shifting chip required
• The default is 4-wire SPI bus, which can choose IIC bus
• Ultra-low power consumption: normal display is only 0.06W (far below the TFT display)
• Military-grade process standards, long-term stable work
• Provides a rich sample program for STM32, C51, Arduino, Raspberry Pi and MSP430 platforms
• Provide underlying driver technical support

Product Parameters

Name	Parameter
Display Color	White, blue, yellow and blue
SKU	MSP154W MSP154B
Screen Size	1.54(inch)
Screen Type	OLED
Driver IC	SSD1309
Resolution	128*64 (Pixel)
Module Interface	4-line SPI、IIC interface
Active Area	35.052x17.516(mm)
Touch Screen Type	have no touch screen
Touch IC	have no IC
Module PCB Size	42.40x38.00(mm)
Visual Angle	>160°
Operating Temperature	-20℃~60℃
Storage Temperature	-30℃~70℃
Operating Voltage	3.3V~5V
Power Consumption	TBD
Rough Weight(Package containing)	12(g)

Interface Definition

Picture 1. Module pin silk screen	Picture 2. Rear view of the module

NOTE:

1.This module supports IIC and 4-wire SPI interface bus mode switching (shown in red box in Figure 2). The details are as follows:

A.Using 4.7K resistance to solder only R5 resistors, then choose 4-wire SPI bus interface (default);

B.Using 4.7K resistance to solder only R4, R9 resistors, then select the IIC bus interface;

2.After the interface bus mode is switched, you need to select the corresponding software and the corresponding wiring pins (as shown in Figure 1)

for the module to operate normally. The corresponding wiring pins are described as follows:

A.select the 4-wire SPI bus interface, all pins need to be used;

B.select the IIC bus interface, connect GND, VCC, SCL, SDA and RES, and connect DC and CS to power ground

3.Weld R8 (as shown in the green box in Figure 2), then the CS pin is grounded, and this pin does not need to be connected

Number	Module Pin	Pin description
1	GND	OLED power ground
2	VCC	OLED power positive (3.3V~5V)
3	SCL	OLED SPI and IIC bus clock signals
4	SDA	OLED SPI and IIC bus data signals
5	RES	OLED reset signal, low level reset (this pin need to connected to the high level (can be connected to the VCC) when selecting IIC bus)
6	DC	Select SPI bus as command/data input selection signal, high level: data, low level: command; When IIC bus is selected, this pin can be used to select IIC slave device address. Select 0x7A for high level and 0x78 for low level;
7	CS	OLED chip select signal, low level enable (this pin need to connected to the power GND when selecting IIC bus)

Product Documentation

• 1.54inch SPI_OLED Module User Manual
• 1.54inch OLED Specification
• 1.54inch SPI_OLED Module Size Picture
• 1.54inch SPI_OLED Module Schematic
• 1.54inch SPI_OLED Module OLED Schematic and PCB Package Library
• Driver IC SSD1309 Datasheet

Program Download

• 1.54inch SPI_OLED Module Package

Reference Materials

• Arduino IDE software use illustration
• RaspberryPi GPIO library installation instructions
• Python Image Library installation instructions
• C51 Keil and stc-isp software use illustration
• STM32 keil software use illustration
• IAR_IDE and MspFet software use illustration
• PCtoLCD2002 software use illustration
• Image2Lcd software use illustration
• Chinese and English display modulo settings

Common Software

• PCtoLCD2002
• Image2Lcd

BACK TO TOP