3.5inch Arduino Display-Mega2560: Difference between revisions

Revision as of 17:48, 27 November 2018

Number	Module Pin	Pin Description	Number	Module Pin	Pin Description
1	5V	Positive power supply	2	5V	Positive power supply
3	DB8	8th bit of data bus	4	DB9	9th bit of data bus
5	DB10	10th bit of data bus	6	DB11	11th bit of data bus
7	DB12	12th bit of data bus	8	DB13	13th bit of data bus
9	DB14	14th bit of data bus	10	DB15	15th bit of data bus
11	DB7	7th bit of data bus	12	DB6	6th bit of data bus
13	DB5	5th bit of data bus	14	DB4	4th bit of data bus
15	DB3	third bit of data bus	16	DB2	2nd bit of data bus
17	DB1	1st bit of data bus	18	DB0	0 bit of data bus
19	RS	LCD register / data selection signal Low level: register, high level: command	20	WR	LCD write control signal
21	CS	LCD screen select control signal, low level enable	22	RST	LCD reset control signal, low reset
23	NC	Undefined, reserved	24	NC	Undefined, reserved
25	NC	Undefined, reserved	26	F_CS	SPI flash chip select control signal
27	NC	Undefined, reserved	28	NC	Undefined, reserved
29	NC	Undefined, reserved	30	NC	Undefined, reserved
31	MISO	SPI bus input signal	32	MOSI	SPI bus output signal
33	CLK	SPI bus clock signal	34	SD_CS	SD card select control signal, low level enable
35	GND	Power ground	36	GND	Power ground


Arduino Mega2560 direct insertion picture

Download the Arduino test program from the Program Download column
For a description of the relevant test procedures, please refer to the test program documentation in the package

Plug the module directly into the Arduino development board ( Do not plug in?)
After the module is plugged in, power on the Arduino board

Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the colligate_test test program as an example):

3.2 inch Arduino Mega2560 module package(The above program is packaged with one click download)

@@ Line 220: / Line 220: @@
 * [http://www.lcdwiki.com/res/MAR3513/3.5inch_Arduino_16BIT_Module_MAR3513_User_Manual_EN.pdf '''3.5 inch Arduino Mega2560 Module User Manual''']
 * [http://www.lcdwiki.com/res/MAR3513/3.5inchQD3503728-Spec-V1.0.pdf '''3.5 inch TFT Specifications''']
-* [http://www.lcdwiki.com/zh/images/7/7f/MAR3513-002.png '''3.5 inch Arduino Mega2560 Module Size Picture''']
+* [http://www.lcdwiki.com/images/7/7f/MAR3513-002.png '''3.5 inch Arduino Mega2560 Module Size Picture''']
 * [http://www.lcdwiki.com/res/MAR3513/Datasheet-ILI9486.pdf '''Driver IC ILI9486 Data sheet''']