1.44inch Arduino SPI Module ST7735S SKU:MAR1441

语言选择 Languages

➤中文

➤EN

Product Picture

Product Description

• 1.44-inch color screen,support 65K color display,display rich colors
• 128X128 resolution, clear display
• Using the SPI serial bus, it only takes a few IOs to illuminate the display
• With SD card slot for convenient function expansion
• Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms
• Military-grade process standards, long-term stable work
• Provide underlying driver technical support

Product Parameters

Name	Parameter
Display Color	16BIT RGB 65K color
SKU	MAR1441
Screen Size	1.44(inch)
Type	TFT
Driver IC	ST7735S
Resolution	128*128 (Pixel)
Module Interface	4-wire SPI interface
Backlight	1 White Led
Active Area	26.2x27.2 (mm)
Module PCB Size	31.49x43.95 (mm)
Operating Temperature	-10℃~60℃
Storage Temperature	-20℃~70℃
Operating Voltage	5V/3.3V
Power Consumption	About 90mw
Product Weight	About 25(g)

Interface Definition

序号	引脚标号	说明
1	VCC	液晶屏电源正(3.3V~5V)
2	GND	液晶屏电源地
3	GND	液晶屏电源地
4	NC	无定义，保留
5	NC	无定义，保留
6	LED	背光控制，高电平点亮，如无需控制则接3.3V常亮
7	CLK	液晶屏SPI总线时钟信号
8	SDI	液晶屏SPI总线写数据信号
9	RS	液晶屏寄存器/数据选择信号，低电平：寄存器，高电平：数据
10	RST	液晶屏复位信号，低电平复位
11	CS	液晶屏片选信号，低电平使能

Number	Pin Label	Pin Description
1	LCD_RST	LCD bus reset signal, low level reset
2	LCD_CS	LCD bus chip select signal, low level enable
3	LCD_RS	LCD bus command / data selection signal, low level: command, high level: data
4	LCD_WR	LCD bus write signal
5	LCD_RD	LCD bus read signal
6	GND	Power ground
7	5V	5V power input
8	3V3	3.3V power input, this pin can be disconnected
9	LCD_D0	LCD 8-bit data Bit0
10	LCD_D1	LCD 8-bit data Bit1
11	LCD_D2	LCD 8-bit data Bit2
12	LCD_D3	LCD 8-bit data Bit3
13	LCD_D4	LCD 8-bit data Bit4
14	LCD_D5	LCD 8-bit data Bit5
15	LCD_D6	LCD 8-bit data Bit6
16	LCD_D7	LCD 8-bit data Bit7
17	SD_SS	SD card SPI bus chip select signal, low level enable
18	SD_DI	SD card SPI bus MOSI signal
19	SD_DO	SD card SPI bus MISO signal
20	SD_SCK	SD card SPI bus clock signal

Product Documentation

• 2.4 inch Arduino UNO Module User Manual
• 2.4 inch Arduino UNO Module Size Picture
• 2.4 inch TFT Specifications
• Driver IC ILI9341 Data sheet

Connect to Arduino

Arduino UNO direct insertion picture	Arduino Mega2560 direct insertion picture

How to use on Arduino

• Step 1: Download the test program

1. Download the Arduino test program from the Program Download column
2. For a description of the relevant test procedures, please refer to the test program documentation in the package

• Step 2: Connect the Arduino development board

1. Plug the module directly into the Arduino development board ( Do not plug in?)
2. After the module is plugged in, power on the Arduino board

• Step 3: Copy the dependent library

1. Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
2. After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

• Step 4: Compile and download the program to the development board

1. Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

• Step 5: Observe the running of the program

1. After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the colligate_test test program as an example):

Program Download

1. Demo_Arduino_8BIT
2. Demo_STC12C5A60S2_8BIT
3. Demo_STM32F103RCT6_8BIT
4. Demo_STM32F103ZET6_8BIT
5. Demo_STM32F407ZGT6_8BIT
6. Demo_STM32F429IGT6_8BIT

• 2.4 inch Arduino UNO module package(The above program is packaged with one click download)

Reference Materials

• Arduino IDE software use illustration
• C51 Keil and stc-isp software use illustration
• STM32 keil software use illustration
• PCtoLCD2002 software use illustration
• Image2Lcd software use illustration
• Chinese and English display modulo settings

Common Software

• PCtoLCD2002
• Image2Lcd

BACK TO TOP