2.0inch Arduino SPI Module ILI9225 SKU:MAR2001: Difference between revisions

Revision as of 11:12, 15 December 2018

2.0-inch color screen,support 16BIT RGB 65K color display,display rich colors
176x220 resolution, clear display
Using the SPI serial bus, it only takes a few IOs to illuminate the display
With SD card slot for convenient function expansion
Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms
Military-grade process standards, long-term stable work
Provide underlying driver technical support

Number	Pin Label	Description
1	VCC	LCD Power positive (3.3V~5V)
2	GND	LCD Power ground
3	GND	LCD Power ground
4	NC	Not defined, reserved
5	NC	Not defined, reserved
6	NC	Not defined, reserved
7	CLK	LCD SPI bus clock signal
8	SDA	LCD SPI bus write data signal
9	RS	LCD register / data selection signal, high level: register, low level: data
10	RST	LCD reset signal, low level reset
11	CS	LCD chip select signal, low level enable


Arduino UNO direct insertion picture	Arduino Mega2560 direct insertion picture

Download the Arduino test program from the Program Download column
For a description of the relevant test procedures, please refer to the test program documentation in the package

Plug the module directly into the Arduino development board ( Do not plug in?)
After the module is plugged in, power on the Arduino board

Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the colligate_test test program as an example):

2.0 inch Arduino SPI Module Package(The above program is packaged with one click download)

@@ Line 185: / Line 185: @@
 ==<font color="blue">Program Download</font> ==
+# [https://yunpan.360.cn/surl_yHciMF3CtXm '''Demo_Arduino_Mega2560&UNO_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHciMEWsjpY '''Demo_Arduino_Mega2560&UNO_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHcikjwh4AG '''Demo_C51_STC12C5A60S2_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHcikWUtQdJ '''Demo_C51_STC12C5A60S2_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHcivHuDwBY '''Demo_C51_STC89C52RC_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHcivXHU9eZ '''Demo_STM32F103RCT6_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHci2JvA2zc '''Demo_STM32F103RCT6_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHci2MzLxaL '''Demo_STM32F103ZET6_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHci2hy2QZY '''Demo_STM32F103ZET6_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHci8uupgFB '''Demo_STM32F407ZGT6_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHci8XCrAPT '''Demo_STM32F407ZGT6_Software_SPI''']
+# [https://yunpan.360.cn/surl_yHciEKvNy8r '''Demo_STM32F429IGT6_Hardware_SPI''']
+# [https://yunpan.360.cn/surl_yHciE2VEP9b '''Demo_STM32F429IGT6_Software_SPI''']
+* [https://yunpan.360.cn/surl_yHciWgyEghB '''2.0 inch Arduino SPI Module Package(The above program is packaged with one click download)''']
 ==<font color="blue">Reference Materials</font> ==