3.5inch RPi Display

语言选择 Languages

➤中文

➤EN

Product Video

Load video

YouTube

YouTube might collect personal data. Privacy Policy

ContinueDismiss

• Related Video

Product Pictures

Features

• 320×480 resolution
• Resistive touch control
• Supports any revision of Raspberry Pi (directly-pluggable)
• Compatible with Raspberry Pi A, B, A+, B+, 2B, 3B, 3B+,4B versions
• Drivers provided (works with your own Raspbian/Ubuntu directly)
• Size perfectly fits the Pi
• High quality immersion gold surface plating
• Supports Raspbian system, ubuntu system ,kali Linux system

Key Parameters

SKU	MPI3501
LCD Type	TFT
LCD Interface	SPI(Fmax:32MHz)
Touch Screen Type	Resistive
Touch Screen Controller	XPT2046
Colors	65536
Driver IC	ILI9486
Backlight	LED
Resolution	320*480 (Pixel)
Backlight Current	120ma
Power Dissipation	0.13A*5V
Operating Temp. (℃)	-20~60
Active Area	48.96x73.44(mm)
Product Size	85.42*55.60(mm)
Package Size	118*72*34 (mm)
Rough Weight(Package containing)	75 (g)

Interface

PIN NO.	SYMBOL	DESCRIPTION
1, 17	3.3V	Power positive (3.3V power input)
2, 4	5V	Power positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16	NC	NC
6, 9, 14, 20, 25	GND	Ground
11	TP_IRQ	Touch Panel interrupt, low level while the Touch Panel detects touching
18	LCD_RS	Instruction/Data Register selection
19	LCD_SI / TP_SI	SPI data input of LCD/Touch Panel
21	TP_SO	SPI data output of Touch Panel
22	RST	Reset
23	LCD_SCK / TP_SCK	SPI clock of LCD/Touch Panel
24	LCD_CS	LCD chip selection, low active
26	TP_CS	Touch Panel chip selection, low active

Driver Installation

This LCD Module need install driver first.

Step 1：Download the Raspbian IMG

https://www.raspberrypi.com/software/operating-systems/

Step 2: Burn the system image

If you don't know how to do that,you can refer to the Raspberry Pi office tutorial

Step 3: Open terminal(SSH) and install the driver on RaspberryPi

(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)

Run:

sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show

Wait A Few Minutes, when the system reboot ok, you can see that.

Touch screen calibration

• This LCD can be calibrated using a program called xinput_calibrator
• Install it with the commands:

cd LCD-show/

sudo dpkg -i -B xinput-calibrator_0.7.5-1_armhf.deb

• Click the Men button on the task bar, choose Preference -> Calibrate Touchscreen.
• Finish the touch calibration following the prompts. Maybe rebooting is required to make calibration active.
• You can create a 99-calibration.conf file to save the touch parameters (not necessary if file exists).

/ect/X11/xorg.conf.d/99-calibration.conf

• Save the touch parameters (may differ depending on LCD) to 99-calibration.conf, as shown in the picture:

How to rotate the display direction

• Step 1，If the driver is not installed, execute the following command (Raspberry Pi needs to connected to the Internet):

sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show  

After execution, the driver will be installed.

• Step 2，If the driver is already installed, execute the following command:

cd LCD-show/
sudo ./rotate.sh 90

After execution, the system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally.
（ ' 90 ' can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees）
If the rotate.sh prompt cannot be found, use Step 1 to install the latest drivers

Download Resources

• Document

1. How_to_install_the_LCD_driver_V1.2
2. How_to_install_matchbox-keyboard
3. How_to_calibrate_the_resistance_touch_screen-V1.2
4. How_to_use_Raspberry_Pi_Getting Star.pdf
5. How_to_change_display_direction-GPIO-Resistive_Touch-V1.2
6. MPI3501-3.5inch-RPi-Display-User-Manual-V1.0

• Driver download

download::LCD-show.tar.gz

• Images download

If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,

Please Try our Configned images for tested.

Just need download and write the image into the TF card. DO NOT need any driver installation steps.

Image Name	Version	Support	Password	Download
Raspbian	2023-12-05	PI4/PI3B+/PI3/ PI2/PI1/ZERO/ZERO W	user:pi password:raspberry	BaiduYun:	MPI3501-3.5inch-2023-12-05-raspios-bookworm-armhf(support Pi4/5) 提取码：n5zl
				Mega:	MPI3501-3.5inch-2022-04-04-raspios-bullseye-armhf.7z
Ubuntu-MATE-32bit	22.04	PI4,PI3B+,PI3,PI2	user:pi password:raspberry	BaiduYun:	MPI3501-3.5inch-ubuntu-mate-22.04-desktop-armhf+raspi.7z 提取码：22e9
				Mega:	MPI3501-3.5inch-ubuntu-mate-22.04-desktop-armhf+raspi.7z
Kali Linux RaspberryPi-32bit	2023.1	PI4B,PI3B+,PI3,PI2	user: kali password: kali	BaiduYun:	MPI3501-3.5inch-kali-linux-2023.1 提取码：vqt3
				Mega:	MPI3501-3.5inch-kali-linux-2022.1

• Software

1. Panasonic SDFormatter
2. Win32DiskImager
3. PuTTY

BACK TO TOP