More actions
Line 16: | Line 16: | ||
==<font color="blue">Product Description</font> == | ==<font color="blue">Product Description</font> == | ||
* | * 1.44-inch color screen,support 65K color display,display rich colors | ||
* 128X128 resolution, clear display | |||
* Using the SPI serial bus, it only takes a few IOs to illuminate the display | |||
* | * With SD card slot for convenient function expansion | ||
* | * Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms | ||
* | |||
* | |||
* Military-grade process standards, long-term stable work | * Military-grade process standards, long-term stable work | ||
* Provide underlying driver technical support | * Provide underlying driver technical support |
Revision as of 10:46, 14 December 2018
Product Video
Product Picture
Product Description
- 1.44-inch color screen,support 65K color display,display rich colors
- 128X128 resolution, clear display
- Using the SPI serial bus, it only takes a few IOs to illuminate the display
- With SD card slot for convenient function expansion
- Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms
- Military-grade process standards, long-term stable work
- Provide underlying driver technical support
Product Parameters
Name | Parameter |
Display Color | RGB 65K color |
SKU | MAR2406 |
Screen Size | 2.4(inch) |
Type | TFT |
Driver IC | ILI9341 |
Resolution | 320*240 (Pixel) |
Module Interface | 8-bit parallel interface |
Active Area | 48.96*36.72(mm) |
Module PCB Size | 72.20*52.7(mm) |
Operating Temperature | -20℃~70℃ |
Storage Temperature | -40℃~70℃ |
Operating Voltage | 5V/3.3V |
Power Consumption | About 90mw |
Product Weight | About 25(g) |
Interface Definition
![](/images/thumb/a/a8/MAR2406-007.png/360px-MAR2406-007.png)
Number | Pin Label | Pin Description |
1 | LCD_RST | LCD bus reset signal, low level reset |
2 | LCD_CS | LCD bus chip select signal, low level enable |
3 | LCD_RS | LCD bus command / data selection signal,
low level: command, high level: data |
4 | LCD_WR | LCD bus write signal |
5 | LCD_RD | LCD bus read signal |
6 | GND | Power ground |
7 | 5V | 5V power input |
8 | 3V3 | 3.3V power input, this pin can be disconnected |
9 | LCD_D0 | LCD 8-bit data Bit0 |
10 | LCD_D1 | LCD 8-bit data Bit1 |
11 | LCD_D2 | LCD 8-bit data Bit2 |
12 | LCD_D3 | LCD 8-bit data Bit3 |
13 | LCD_D4 | LCD 8-bit data Bit4 |
14 | LCD_D5 | LCD 8-bit data Bit5 |
15 | LCD_D6 | LCD 8-bit data Bit6 |
16 | LCD_D7 | LCD 8-bit data Bit7 |
17 | SD_SS | SD card SPI bus chip select signal, low level enable |
18 | SD_DI | SD card SPI bus MOSI signal |
19 | SD_DO | SD card SPI bus MISO signal |
20 | SD_SCK | SD card SPI bus clock signal |
Product Documentation
- 2.4 inch Arduino UNO Module User Manual
- 2.4 inch Arduino UNO Module Size Picture
- 2.4 inch TFT Specifications
- Driver IC ILI9341 Data sheet
Connect to Arduino
![]() |
![]() |
---|---|
Arduino UNO direct insertion picture | Arduino Mega2560 direct insertion picture |
How to use on Arduino
- Step 1: Download the test program
- Download the Arduino test program from the Program Download column
- For a description of the relevant test procedures, please refer to the test program documentation in the package
- Step 2: Connect the Arduino development board
- Plug the module directly into the Arduino development board ( Do not plug in?)
- After the module is plugged in, power on the Arduino board
- Step 3: Copy the dependent library
- Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
- After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:
- (1) Decompress the downloaded test package
- (2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder
- of the Arduino project directory ( Don't know the Arduino project directory?)
- Step 4: Compile and download the program to the development board
- Open the sample in the Example directory of the package to test, compile and download( Don't know how to compile and download?)
- Step 5: Observe the running of the program
- After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs
- successfully, as shown in the following figure (take the colligate_test test program as an example):
Program Download
- Demo_Arduino_8BIT
- Demo_STC12C5A60S2_8BIT
- Demo_STM32F103RCT6_8BIT
- Demo_STM32F103ZET6_8BIT
- Demo_STM32F407ZGT6_8BIT
- Demo_STM32F429IGT6_8BIT
Reference Materials
- Arduino IDE software use illustration
- C51 Keil and stc-isp software use illustration
- STM32 keil software use illustration
- PCtoLCD2002 software use illustration
- Image2Lcd software use illustration
- Chinese and English display modulo settings