More actions
| Line 39: | Line 39: | ||
| align="center" |2.4(inch) | | align="center" |2.4(inch) | ||
|- | |- | ||
| align="center" |Type | | align="center" |Screen Type | ||
| align="center" |TFT | | align="center" |TFT | ||
|- | |- | ||
| Line 49: | Line 49: | ||
|- | |- | ||
| align="center" |Module Interface | | align="center" |Module Interface | ||
| align="center" |16Bit parallel interface | | align="center" |8Bit or 16Bit parallel interface | ||
|- | |- | ||
| align="center" |Active Area | | align="center" |Active Area | ||
| align="center" |48.96*36.72(mm) | | align="center" |48.96*36.72(mm) | ||
|- | |||
|Touch Screen Type | |||
|resistive touch screen | |||
|- | |||
|Touch IC | |||
|XPT2046 | |||
|- | |- | ||
| align="center" |Module PCB Size | | align="center" |Module PCB Size | ||
| Line 78: | Line 84: | ||
The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows: | The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows: | ||
:Soldering '''R1''': Use '''16'''-bit data bus mode (default) | :Soldering '''R1''': Use '''16'''-bit data bus mode (default) | ||
:Soldering '''R2''': Use '''8'''-bit data bus mode | :Soldering '''R2''': Use '''8'''-bit data bus mode | ||
| Line 244: | Line 251: | ||
# Find the TFTLCD interface on the development board, connect the module pins and interfaces, and then plug them directly into | # Find the TFTLCD interface on the development board, connect the module pins and interfaces, and then plug them directly into | ||
::the interface(for the connection method, please refer to the instructions of the ALIENTEK STM32 development board) | ::the interface(for the connection method, please refer to the instructions of the ALIENTEK STM32 development board) | ||
Revision as of 17:08, 11 May 2019
Product Video
Product Picture
Product Description
- 2.4-inch color screen, support 16BIT RGB 65K color display, display rich colors
- 240x320 resolution for clear display
- Support 8-bit/16-bit parallel bus switching (the default is 16-bit), fast transfer speed
- Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development boards for direct plug-in use
- Support for touch function
- Support SD card function expansion
- Provides a rich sample program for STM32 and C51 platforms
- Military-grade process standards, long-term stable work
- Provide underlying driver technical support
Product Parameters
| Name | Parameter |
| Display Color | 16BIT RGB 65K color |
| SKU | MRB2408 |
| Screen Size | 2.4(inch) |
| Screen Type | TFT |
| Driver IC | ILI9341 |
| Resolution | 320*240 (Pixel) |
| Module Interface | 8Bit or 16Bit parallel interface |
| Active Area | 48.96*36.72(mm) |
| Touch Screen Type | resistive touch screen |
| Touch IC | XPT2046 |
| Module PCB Size | 44.25x76.00 (mm) |
| Operating Temperature | -20℃~70℃ |
| Storage Temperature | -40℃~70℃ |
| Operating Voltage | 3.3V/5V |
| Power Consumption | TBD |
| Product Weight | TBD |
Interface Definition
The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows:
- Soldering R1: Use 16-bit data bus mode (default)
- Soldering R2: Use 8-bit data bus mode
| Number | Pin Label | Description |
| 1 | CS | LCD reset control pin( low level enable) |
| 2 | RS | LCD register / data selection control pin(high level: register, low level: data) |
| 3 | WR | LCD write control pin |
| 4 | RD | LCD read control pin |
| 5 | RST | LCD reset control pin( low level reset) |
| 6 | D1 | LCD data bus low 8-bit pin |
| 7 | D2 | |
| 8 | D3 | |
| 9 | D4 | |
| 10 | D5 | |
| 11 | D6 | |
| 12 | D7 | |
| 13 | D8 | |
| 14 | D10 | LCD data bus high 8-bit pin |
| 15 | D11 | |
| 16 | D12 | |
| 17 | D13 | |
| 18 | D14 | |
| 19 | D15 | |
| 20 | D16 | |
| 21 | D17 | |
| 22 | SCS | SD card selection control pin (used when using the SD card expansion function, this test program is not used) |
| 23 | BL | LCD backlight control pin(High level light) |
| 24 | VDD | Module power positive pin (module has integrated voltage regulator IC, so the power supply can be connected to 5V or 3.3V) |
| 25 | VDD | |
| 26 | GND | Module power ground pin |
| 27 | GND | |
| 28 | V5 | LCD backlight power positive pin (default shared onboard backlight power supply, this pin can not be connected) |
| 29 | MO | Touch screen SPI bus data input pin |
| 30 | MI | Touch screen SPI bus data output pin |
| 31 | PEN | Touch screen interrupt detection pin(Low level when a touch occurs) |
| 32 | FCS | Flash chip select control pin (used when using the Flash extension function, this test program is not used) |
| 33 | TCS | Touch screen IC chip select control pin(Low level enable) |
| 34 | CLK | Touch screen SPI bus clock control pin |
Product Documentation
- 2.4inch 16bit Parallel-Port Module User Manual
- 2.4inch TFTLCD Specification
- 2.4inch 16bit Parallel-Port Module Size Picture
- 2.4inch 16bit Parallel-Port Module Schematic
- 2.4inch 16bit Parallel-Port Module LCD Schematic and PCB Package Library
- Voltage Regulator IC ME6206 Data sheet
- touch screen control IC TSC2406 Data sheet
- Driver IC ILI9341 Data sheet
Program Download
Reference Materials
- C51 Keil and stc-isp software use illustration
- STM32 keil software use illustration
- PCtoLCD2002 software use illustration
- Image2Lcd software use illustration
- Chinese and English display modulo settings
How to use on STM32 development board
This module is compatible with the ALIENTEK STM32 development board. The specific usage is as follows:
- Step 1: Download the test program
- Download the STM32 Mini development board IO emulation or other development board FSMC test program from the Program Download column (only these programs support the STM32 development board in-line)
- You can also download the standard routines that come with the punctual atomic STM32 development board
- For a description of the relevant test procedures, please refer to the test program documentation in the package
- Step 2: Connect the STM32 development board
- Find the TFTLCD interface on the development board, connect the module pins and interfaces, and then plug them directly into
- the interface(for the connection method, please refer to the instructions of the ALIENTEK STM32 development board)
- Step 3: Compile and download the program to the development board
- Compile and download the program you need to test to the STM32 development board（ Don't know how to compile and download?）
- Step 4: Observe the running of the program
- After the program is finished, observe the running status of the program. If it can be displayed normally, the program runs successfully.