MHS-3.2inch Display

语言选择 Languages

➤中文

➤EN

Product Pictures

Product Features

• Physical resolution 320 x 480, with resistive touch control
• It supports up to 125MHz SPI signal input, showing stable no screen and no flicker
• With the Raspberry Pi, the refresh rate is about 60FPS, playing video games is no problem.
• Support FBCP software driver, support dual screen display, can be adjusted by software to adjust the resolution
• Same size as the Raspberry Pi, perfectly compatible and can be directly inserted into any version of the Raspberry Pi (Raspberry Pi ZeroW, A, A+, B, B+, 2B, 3B, 3B+)
• Support for Raspbian/Ubuntu/Kali/Retropie systems, providing drivers and mirroring
• This product has passed CE and RoHS certification

Main Parameters

Name	Description
SKU	MHS3232
Screen Size	3.2inch
LCD Type	TFT
Module Interface	SPI (upports up to 125MHz SPI input)
Resolution	320*240 (Pixel)
Touch Screen Controller	XPT2046
LCD Driver IC	ILI9341
Backlight	LED
Power Consumption	0.16A*5V
Operating Temperature（℃）	-20~60
Module PCB Size	84.91*56.54 (mm)
Package Size	118*72*34 (mm)
Rough Weight(Package containing)(g)	73(g)

Hardware Description

• Interface Definition

Pin Number	Identification	Description
1, 17	3.3V	Power supply (3.3V power input)
2, 4	5V	Power supply (5V power input)
3, 5, 7, 8, 10,22	NC	Not connected
6, 9, 14, 20, 25	GND	Power ground
11	TP_IRQ	The touch panel is interrupted, and it is detected that the touch panel is pressed low.
15	LCD_RS	Instruction/data register selection, low level is instruction, high level is data
19	LCD_SI / TP_SI	LCD display / touch panel SPI data input
21	TP_SO	Touch panel SPI data output
13	RST	Reset signal, low reset
23	LCD_SCK / TP_SCK	LCD display / touch panel SPI clock signal
24	LCD_CS	LCD chip select signal, low level enable
26	TP_CS	Touch panel chip select signal, low level enable
12	KEY1	Button 1
16	KEY2	Button 2
18	KEY3	Button 3

• Product Size

How to use in the Raspberry/Ubuntu Mate/Kali/Retropie system

There are two ways to use it

The First Method

Directly download the image we created and burn it into the micro SD card and insert it into the RaspberryPi. (Q:How to burn?)

Image download see the image download section of the Download Resources

The second method

Step 1, install the latest official image of various systems (Q:How to install？)

(1)Download the latestRaspbian/Ubuntu Mate/Kali-linux/Retropieimage from the official

(2) Format the Micro SD card using SDFormatter

(3) Use Win32DiskImager to burn the official image to the Micro SD card

Step 2, connect with the Raspberry Pi

Align right-side to insert the LCD screen             

Plug-in MicroSD card, connect network and power   

Step 3, install the LCD driver

A. Install on the Raspbian system (the Raspberry Pi needs to connect to the Internet)

(1) Log in to the Raspberry Pi terminal(SSH remote login user name and password, see the image download of the Download Resources) (Q:The ssh can't connect?)

(2) Execute the following command to get the LCD driver and install it (after copying, click the right mouse button in the Putty window to paste):

sudo rm -rf LCD-show git clone https://github.com/goodtft/LCD-show.git chmod -R 755 LCD-show cd LCD-show/ sudo ./MHS32-show

B. Install on the Ubuntu Mate, Kali, Retropie system

(1) Download the local driver, the download link is as follows: (Because of system differences, the driver downloaded from github cannot run normally

in the three systems Ubuntu Mate, Kali, Retropie, so only local drivers can be used)

Driver download for Ubuntu-mate-18.04 system:LCD-show.tar.gz

Driver download for Kali-linux system:LCD-show.tar.gz

Driver download for the retropie-rpi2_rpi3 system:LCD-show.tar.gz

Driver download for retropie-rpi1_zero system:LCD-show.tar.gz

(2) Log in to the Raspberry Pi terminal(SSH remote login user name and password, see the image download of the Download Resources) (Q:The ssh can't connect?)

(3) Copy the local driver to the running Raspberry Pi system and execute the following command to extract it (can be copied by SD card or FileZilla software)

tar -xvzf LCD-show.tar.gz

(4) Execute the following command to install the LCD driver

chmod -R 755 LCD-show cd LCD-show/ sudo ./MHS32-show

Step 4, Check if the driver is successfully installed

(1) After the LCD driver is installed, the system will automatically restart. After the startup is successful, the LCD can display and touch normally,

indicating that the driver installation is successful.

Note:

A. Ubuntu system default SSH is not enabled, the specific method of opening seeRaspberryPi Ubuntu-mate open ssh instructions

B. Ubuntu-18.04 system ssh connection may fail, the specific solution is shown in RaspberryPi Ubuntu-mate-18.04 ssh connection failure solution description

C. The retropie-rpi1_zero system cannot log in via SSH (no network port and wifi module). You need to copy the driver through the serial port. For details, see RaspberryPi Zero open serial instructions

D. Retropie system game installation and setup instructions see RaspberryPi Retropie using instructions

How to rotate the display direction

This method only applies to the Raspberry Pi series of display screens, other display screens do not apply.

• Method 1，If the driver is not installed, execute the following command (Raspberry Pi needs to connected to the Internet):

sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./XXX-show 90

After execution, the driver will be installed. The system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally.
（ ' XXX-show ' can be changed to the corresponding driver, and ' 90 ' can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees）

• Method 2，If the driver is already installed, execute the following command:

cd LCD-show/
sudo ./rotate.sh 90

After execution, the system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally.
（ ' 90 ' can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees）
If the rotate.sh prompt cannot be found, use Method 1 to install the latest drivers

FAQ

• How to resolve the issue of touch flip in resistive touch production
• HDMI display does not display after installing FBCP driver

Download Resources

• Document

1. MHS-3.2inch Display quick start
2. MHS-3.2inch Display user manual
3. How to install the LCD driver
4. How to calibrate the resistance touch screen
5. How to install matchbox-keyboard
6. How to change display direction GPIO resistive touch
7. How to use Raspberry Pi(Download,Format,Burn,SSH,PuTTy)
8. RaspberryPi Ubuntu-mate open ssh instructions
9. RaspberryPi Ubuntu-mate-18.04 ssh connect
10. RaspberryPi Zero open serial instructions
11. RaspberryPi Retropie using instructions

• Images Download

If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,

Please Try our Configned images for tested.

Just need download and write the image into the TF card. DO NOT need any driver installation steps.

System Name	System Version	Raspberry Pi version	User and passwd	Download Link
Raspbian	2019-09-26	PI4/PI3B+/PI3/PI2/ PI1/ZERO/ZERO W	user: pi password: raspberry	BaiduYun:	MHS3232-3.2inch-2019-09-26-raspbian-buster.7z Fetch Code：7dq2
				Mega:	MHS3232-3.2inch-2019-09-26-raspbian-buster.7z
Ubuntu-mate	18.04.2-beta1	PI3B+,PI3,PI2	user: pi password: raspberry	BaiduYun:	MHS32-ubuntu-mate-18.04.2-beta1-armhf+raspi-ext4.7z Fetch Code：g0cu
				Mega:	MHS32-ubuntu-mate-18.04.2-beta1-armhf+raspi-ext4.7z
Kali Linux RaspberryPi 2,3and4	2019.4	PI4B,PI3B+,PI3,PI2	user: root password: toor	BaiduYun:	MHS3228-3.2inch-Kali-2019.7.7z Fetch Code：2khf
				Mega:	MHS3228-3.2inch-Kali-2019.4.7z
RetroPie-rpi2_rpi3	4.4	PI3B+,PI3,PI2	user: pi password: raspberry	BaiduYun:	MHS32-retropie-4.4-rpi2_rpi3.7z Fetch Code：dc90
				Mega:	MHS32-retropie-4.4-rpi2_rpi3.7z
RetroPie-rpi1_zero	4.4	Pi1/ZERO/ZERO W	user: pi password: raspberry	BaiduYun:	MHS32-retropie-4.4-rpi1_zero.7z Fetch Code：s42y
				Mega:	MHS32-retropie-4.4-rpi1_zero.7z

• MD5 checksum of the image files
• Common software

1. Panasonic SDFormatter
2. Win32DiskImager
3. PuTTY

BACK TO TOP