More actions
Product Video
Product Pictures
Features
- 320×480 resolution
- Resistive touch control
- Supports any revision of Raspberry Pi (directly-pluggable)
- Compatible with Raspberry Pi A, B, A+, B+, 2B, 3B, 3B+versions
- Drivers provided (works with your own Raspbian/Ubuntu directly)
- Size perfectly fits the Pi
- High quality immersion gold surface plating
- Supports Raspbian system, ubuntu system ,kali Linux system
Key Parameters
SKU | MPI3501 |
LCD Type | TFT |
LCD Interface | SPI(Fmax:32MHz) |
Touch Screen Type | Resistive |
Touch Screen Controller | XPT2046 |
Colors | 65536 |
Backlight | LED |
Resolution | 320*480 (Pixel) |
Backlight Current | 120ma |
Power Dissipation | 0.13A*5V |
Operating Temp. (℃) | -20~60 |
Package Size | 118*72*34 (mm) |
Rough Weight | 75 (g) |
Interface
PIN NO. | SYMBOL | DESCRIPTION |
---|---|---|
1, 17 | 3.3V | Power positive (3.3V power input) |
2, 4 | 5V | Power positive (5V power input) |
3, 5, 7, 8, 10, 12, 13, 15, 16 | NC | NC |
6, 9, 14, 20, 25 | GND | Ground |
11 | TP_IRQ | Touch Panel interrupt, low level while the Touch Panel detects touching |
18 | LCD_RS | Instruction/Data Register selection |
19 | LCD_SI / TP_SI | SPI data input of LCD/Touch Panel |
21 | TP_SO | SPI data output of Touch Panel |
22 | RST | Reset |
23 | LCD_SCK / TP_SCK | SPI clock of LCD/Touch Panel |
24 | LCD_CS | LCD chip selection, low active |
26 | TP_CS | Touch Panel chip selection, low active |
Driver Installation
This LCD Module need install driver first.
Step 1:Download the Raspbian IMG
https://www.raspberrypi.org/downloads/raspbian/
Step 2: Burn the system image
If you don't know how to do that,you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)
Run:
sudo rm -rf LCD-show git clone https://github.com/Lcdwiki/LCD-show.git chmod -R 755 LCD-show cd LCD-show/ sudo ./LCD35-show
Wait A Few Minutes, when the system reboot ok, you can see that.
Touch screen calibration
- This LCD can be calibrated using a program called xinput_calibrator
- Install it with the commands:
cd LCD-show/
sudo dpkg -i -B xinput-calibrator_0.7.5-1_armhf.deb
- Click the Men button on the task bar, choose Preference -> Calibrate Touchscreen.
- Finish the touch calibration following the prompts. Maybe rebooting is required to make calibration active.
- You can create a 99-calibration.conf file to save the touch parameters (not necessary if file exists).
/ect/X11/xorg.conf.d/99-calibration.conf
- Save the touch parameters (may differ depending on LCD) to 99-calibration.conf, as shown in the picture:
Download Resources
- Document
- How_to_install_the_LCD_driver_V1.2
- How_to_install_matchbox-keyboard
- How_to_calibrate_the_resistance_touch_screen-V1.2
- How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf
- How_to_change_display_direction-GPIO-Resistive_Touch-V1.2
- MPI3501-3.5inch-RPi-Display-User-Manual-V1.0
- Driver download
- download::LCD-show.tar.gz
- Images download
- If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,
- Please Try our Configned images for tested.
- Just need download and write the image into the TF card. DO NOT need any driver installation steps.
Image Name | Version | Support | Password | Download | |
---|---|---|---|---|---|
Raspbian | 2019-06-20 | PI3B+/A/A+/B/B+/PI2/
PI3/ZERO/ZERO W |
user:pi
password:raspberry |
![]() |
MPI3501-3.5inch-2019-06-20-Raspbian-buster.7z Fetch Code:ev5g |
![]() |
MPI3501-3.5inch-2019-06-20-Raspbian-buster.7z | ||||
Ubuntu | Mate:18.04.2 | PI3B+,PI3,PI2 | user:pi
password:raspberry |
![]() |
MPI3501-3.5inch-Ubuntu-18.04.2.7z Fetch Code:mxjx |
![]() |
MPI3501-3.5inch-Ubuntu-18.04.2.7z | ||||
Kali-linux | 2019.1 | PI3B+,PI3,PI2 | user:root
password:toor |
![]() |
MPI3501-3.5inch-Kali-2019.1.7z Fetch Code:i8ew |
![]() |
MPI3501-3.5inch-Kali-2019.1.7z |
- MD5 of Image
- Software