2.4inch 16BIT Module ILI9341 SKU:MRB2408

Product Picture

2.4-inch color screen, support 16BIT RGB 65K color display, display rich colors
240x320 resolution for clear display
Support 8-bit/16-bit parallel bus switching (the default is 16-bit), fast transfer speed
Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development boards for direct plug-in use
Support for touch function
Support SD card function expansion
Provides a rich sample program for STM32 and C51 platforms
Military-grade process standards, long-term stable work
Provide underlying driver technical support

Name	Parameter
Display Color	16BIT RGB 65K color
SKU	MRB2408
Screen Size	2.4(inch)
Screen Type	TFT
Driver IC	ILI9341
Resolution	320*240 (Pixel)
Module Interface	8Bit or 16Bit parallel interface
Active Area	48.96*36.72(mm)
Touch Screen Type	resistive touch screen
Touch IC	XPT2046
Module PCB Size	44.25x76.00 (mm)
Operating Temperature	-20℃~60℃
Storage Temperature	-30℃~70℃
Operating Voltage	3.3V/5V
Power Consumption	TBD
Rough Weight(Package containing)	35 (g)

The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows:

Only soldering R1: select 16-bit data bus mode (default), use D1~D8, D10~D17 data pins

Only soldering R2: select 8-bit data bus mode, use D10~D17 data pins

Number	Pin Label	Description
1	CS	LCD reset control pin( low level enable)
2	RS	LCD register / data selection control pin(high level: register, low level: data)
3	WR	LCD write control pin
4	RD	LCD read control pin
5	RST	LCD reset control pin( low level reset)
6	D1	LCD data bus low 8-bit pin(When 8-bit parallel data bus mode is selected, the lower 8-bit data pins are not used)
7	D2
8	D3
9	D4
10	D5
11	D6
12	D7
13	D8
14	D10	LCD data bus high 8-bit pin
15	D11
16	D12
17	D13
18	D14
19	D15
20	D16
21	D17
22	SCS	SD card selection control pin (used when using the SD card expansion function, this test program is not used)
23	BL	LCD backlight control pin(High level light)
24	VDD	Module power positive pin (module has integrated voltage regulator IC, so the power supply can be connected to 5V or 3.3V)
25	VDD
26	GND	Module power ground pin
27	GND	Module power ground pin
28	V5	LCD backlight power positive pin (default shared onboard backlight power supply, this pin can not be connected)
29	MO	Touch screen SPI bus data input pin
30	MI	Touch screen SPI bus data output pin
31	PEN	Touch screen interrupt detection pin(Low level when a touch occurs)
32	FCS	Flash chip select control pin (used when using the Flash extension function, this test program is not used)
33	TCS	Touch screen IC chip select control pin(Low level enable)
34	CLK	Touch screen SPI bus clock control pin

This module is compatible with the ALIENTEK STM32 development board. The specific usage is as follows:

Download the STM32 test program from the Program Download column
For a description of the relevant test procedures, please refer to the test program documentation in the package

Find the TFTLCD Slot on the development board, connect the module pins and Slot(For example, the module CS pin corresponds to the slot CS pin),

and then plug them directly into the Slot

Compile and download the program you need to test to the STM32 development board（ Don't know how to compile and download?）

After the program is finished, observe the running status of the program. If it can be displayed normally, the program runs successfully.