Toggle menu
Toggle personal menu
Not logged in
Your IP address will be publicly visible if you make any edits.

2.8inch 16BIT Module ILI9341 SKU:MRB2801

From LCD wiki

语言选择

Languages

➤中文
➤EN


Product Picture

Product Description

  • 2.8-inch color screen, support 16BIT RGB 65K color display, display rich colors
  • 240x320 resolution for clear display
  • Support 8-bit/16-bit parallel bus switching (the default is 16-bit), fast transfer speed
  • Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development boards for direct plug-in use
  • Support for touch function
  • Support SD card function expansion
  • Provides a rich sample program for STM32 and C51 platforms
  • Military-grade process standards, long-term stable work
  • Provide underlying driver technical support

Product Parameters

Name Parameter
Display Color 16BIT RGB 65K color
SKU MRB2801
Screen Size  2.8(inch)
Screen Type TFT
Driver IC ILI9341
Resolution 320*240 (Pixel)
Module Interface 8bit or 16Bit parallel interface
Active Area  43.2x57.6 (mm)
Touch Screen Type resistive touch screen
Touch IC XPT2046
Module PCB Size 51.00x82.55 (mm)
Operating Temperature -20℃~60℃
Storage Temperature -30℃~70℃
Operating Voltage 3.3V/5V
Power Consumption TBD
Rough Weight(Package containing) 44 (g)

Interface Definition

The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows:

Solder R5 with 0Ω resistor or short circuit directly, and disconnect R4: select 16-bit data bus mode (default), use DB0~DB15 data pin
Solder R4 with 0Ω resistor or short circuit directly, and disconnect R5: select 8-bit data bus mode, use DB8~DB15 data pin
Number Pin Label Description
1 CS LCD reset control pin( low level enable)
2 RS LCD register / data selection control pin(high level: register, low level: data)
3 WR LCD write control pin
4 RD LCD read control pin 
5 RST LCD reset control pin( low level reset)
6 DB0 LCD data bus low 8-bit pin(When 8-bit parallel data bus mode is selected, the lower 8-bit data pins are not used)
7 DB1
8 DB2
9 DB3
10 DB4
11 DB5
12 DB6
13 DB7
14 DB8 LCD data bus high 8-bit pin
15 DB9
16 DB10
17 DB11
18 DB12
19 DB13
20 DB14
21 DB15
22 SDCS SD card selection control pin (used when using the SD card expansion function, this test program is not used)
23 BL LCD backlight control pin(High level light)
24 VDD Module power positive pin (module has integrated voltage regulator IC, so the power supply can be connected to 5V or 3.3V)
25 VDD
26 GND Module power ground pin
27 GND
28 NC Undefined, reserved
29 MISO Touch screen SPI bus data input pin
30 MOSI Touch screen SPI bus data output pin
31 PEN Touch screen interrupt detection pin(Low level when a touch occurs)
32 F_CS Flash chip select control pin (used when using the Flash extension function, this test program is not used)
33 T_CS Touch screen IC chip select control pin(Low level enable)
34 CLK Touch screen SPI bus clock control pin

How to use on STM32 development board

This module is compatible with the ALIENTEK STM32 development board. The specific usage is as follows:

  • Step 1: Download the test program
  1. Download the STM32 test program from the Program Download column
  2. For a description of the relevant test procedures, please refer to the test program documentation in the package
  • Step 2: Connect the STM32 development board
  1. Find the TFTLCD Slot on the development board, connect the module pins and Slot(For example, the module CS pin corresponds to the slot CS pin),
and then plug them directly into the Slot
  • Step 3: Compile and download the program to the development board
  1. Compile and download the program you need to test to the STM32 development board( Don't know how to compile and download?
  • Step 4: Observe the running of the program
  1. After the program is finished, observe the running status of the program. If it can be displayed normally, the program runs successfully.

Program Download

Product Documentation

Reference Materials

Common Software

BACK TO TOP