More actions
Product Pictures
Product Description
- 4.0-inch IPS full-angle display, support HDMI input, refresh rate up to 60FPS
- The physical resolution is 800x480
- Raspberry Pi monitor with touch control (need to install touch driver)
- It can be used as standard HDMI output device for computer display(no touch function)
- Compatible with and can be directly inserted into all versions of raspberry PI motherboards (raspberry PI 1 generation B and Zero need additional HDMI cable)
- Support HDMI audio output, backlight brightness adjustable
Product Parameters
SKU | MPI4008 |
Screen Size | 4.0inch |
LCD Type | TFT |
Module Interface | HDMI |
Resolution | 800*480 (Pixel) |
Touch Screen Controller | XPT2046 |
LCD Driver IC | NT35510 |
Backlight | LED |
power consumption | 0.16A*5V |
Working temperature(℃) | -20~70 |
Module PCB Size | 98.60*58.05 (mm) |
Package Size | 143*134*51 (mm) |
Product Weight(g) | 125 (g) |
Hardware Description
- ① 3.5mm Headphone Jack: Output audio signal
- ② HDMI:Used to connect the main board and LCD display for HDMI transmission
- ③ Micro USB:Get 5V Power from USB, If ⑤-13*2 Pin Socket has been connected, that this USB interface can be No Connect.
- ④ Backlight adjustment button: Short press backlight change 10%, long press a few seconds to close backlight; short press to open backlight
- ⑤ 13*2 Pin Socket:Get +5V Power from raspberry Pi to LCD, at the same time transfer touch signal back to Raspberry Pi.
- 13*2 Pin Socket interface definition:
Pin | Name | Description |
1、17 | 3.3V | Power supply +3.3V |
2、4 | 5V | Power supply +5V |
3、5、7、8、10、11、12、13、15、16、18、24 | NC | NC |
6、9、14、20、25 | GND | GND |
19 | TP_SI | SPI data input of touch panel |
21 | TP_SO | SPI data output of touch panel |
22 | TP_IRQ | The touch panel is interrupted and the low level is detected when the touch panel is pressed down |
23 | TP_SCK | Touch the SPI clock signal of the panel |
26 | TP_CS | Touch panel select signal, low level select touch panel |
- Dimension drawing
How to use Raspbian/Ubuntu Mate/Kali/Retropie system
Method 1
1) Download the driver image file from the website:
http://www.lcdwiki.com/4inch_HDMI_Display-C#Download_Resources
2) Format Micro SD card by SDFormatter
3) Burn the official image into Micro SD card by using Win32DiskImager.
4) Insert Micro SD card, connect LCD, start Raspberry Pi, and it will work normally.
Method 2
- Step 1: install the latest official images of various systems (Q:Don‘t know how to install?)
- 步骤2, 与树莓派连接
- 如图将液晶屏母座靠右对齐树莓派排针插入,插入HDMI转接头,插入MicroSD卡,连接网线,接好电源
- 步骤3, 安装LCD驱动
- A、在Raspbian系统中安装(树莓派需要连接互联网)
- (1)登陆树莓派终端(SSH远程登录用户名和密码见资源下载的镜像下载) (Q:SSH无法连接?)
- (2)执行以下命令获取LCD驱动并安装(复制后在Putty窗口中单击鼠标右键即可粘贴):
sudo rm -rf LCD-show git clone https://github.com/goodtft/LCD-show.git chmod -R 755 LCD-show cd LCD-show/ sudo ./MPI4008-show |
- B、在Ubuntu、Kali、RetroPie系统中安装
- (1)下载本地驱动,下载链接如下:(因为系统差异,Ubuntu、Kali、RetroPie系统暂时只能使用本地驱动)
- 适用于Ubuntu-mate-18.04系统的驱动下载: Ubuntu-18.04-驱动
- 适用于Kali-linux系统的驱动下载:Kali-2019.1-驱动
- 适用于retropie-rpi2_rpi3系统的驱动下载:RetroPie-Pi2-Pi3-驱动
- 适用于retropie-rpi1_zero系统的驱动下载:RetroPie-Pi1-ZERO-驱动
- (2)将本地驱动复制到树莓派系统Micro SD卡的根目录 (推荐步骤1烧录完成后,将驱动直接拷贝到Micro SD卡根目录里)
- (3)登陆树莓派终端,并执行以下命令安装驱动 (SSH远程登录用户名和密码见资源下载的镜像下载)
- (1)下载本地驱动,下载链接如下:(因为系统差异,Ubuntu、Kali、RetroPie系统暂时只能使用本地驱动)
- B、在Ubuntu、Kali、RetroPie系统中安装
cd /boot tar -xvzf LCD-show.tar.gz chmod -R 755 LCD-show cd LCD-show/ sudo ./MPI4008-show |
- 步骤4, 检测驱动是否安装成功
- LCD驱动安装完成后,系统会自动重启,LCD可以正常显示和触摸就说明驱动安装成功了
注意事项:
- A、Ubuntu系统默认SSH没有开启,具体开启方法见RaspberryPi Ubuntu-mate系统开启SSH说明
- B、Ubuntu-18.04系统ssh连接可能会失败,具体解决方法见RaspberryPi Ubuntu-mate-18.04系统ssh连接失败解决方法说明
- C、RetroPie-rpi1_zero系统不能通过SSH登录(没有网口和wifi模块),需要通过串口拷贝驱动,具体设置方法见RaspberryPi Zero打开串口说明
- D、Retropie系统游戏安装及设置说明见RaspberryPi Retropie系统使用说明
How to use as PC Monitor
- Connected the computer HDMI output to the LCD HDMI interface by HDMI cable.
- Power to Micro USB interface
- If you have multiple monitors, please pull the other displayer, and make this LCD as the only displayer for testing.
- As computer monitors, the touch function will not be available.
Download resources
- Documents
- How_to_install_the_LCD_driver_V1.2
- How_to_install_matchbox-keyboard
- How_to_calibrate_the_resistance_touch_screen-V1.2
- How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf
- How_to_change_display_direction-GPIO-Resistive_Touch-V1.2
- Driver Download
- Image Download
- If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,
- Please Try our Configned images for tested.
- Just need download and write the image into the Micro SD card. DO NOT need any driver installation steps.
Image Name | Version | Support | Password | Download | |
---|---|---|---|---|---|
Raspbian | 20190408 | PI3B+/A/A+/B/B+/PI2/
PI3/ZERO/ZERO W |
user:pi
password:raspberry |
360Yun: | MPI4008-4inch-HDMI-C-Raspbian-20190408.7z |
Mega: | MPI4008-4inch-HDMI-C-Raspbian-20190408.7z | ||||
Ubuntu | 18.04.02 | PI3B+,PI3B,PI2B | user:pi
password:raspberry |
360Yun: | MPI4008-4inch-HDMI-C-Ubuntu-18.04.02.7z |
Mega: | MPI4008-4inch-HDMI-C-Ubuntu-18.04.2.7z | ||||
Kali-linux | 2019.1 | PI3B+,PI3,PI2 | user:root
password:toor |
360Yun: | MPI4008-4inch-HDMI-C-Kali-2019.1.7z |
Mega: | MPI4008-4inch-HDMI-C-Kali-2019.1.7z | ||||
RetroPie | 4.4 | Pi1,Pi-ZERO | user:pi
password:raspberry |
360Yun: | MPI4008-4inch-HDMI-C-retropie-4.4-rpi1-zero.7z |
Mega: | MPI4008-4inch-HDMI-C-retropie-4.4-rpi1-zero.7z | ||||
RetroPie | 4.4 | Pi3B+,Pi3,Pi2 | user:pi
password:raspberry |
360Yun: | MPI4008-4inch-HDMI-C-retropie-4.4-rpi2-rpi3.7z |
Mega: | MPI4008-4inch-HDMI-C-retropie-4.4-rpi2-rpi3.7z |
- MD5 of Image
- Common Software