4inch HDMI Display-C
Contents
Product Pictures
Product Description
- 4.0-inch IPS full-angle display, support HDMI input, refresh rate up to 60FPS
- The physical resolution is 800x480
- Raspberry Pi monitor with touch control (need to install touch driver)
- It can be used as standard HDMI output device for computer display(no touch function)
- Compatible with and can be directly inserted into all versions of raspberry PI motherboards (raspberry PI 1 generation B and Zero need additional HDMI cable)
- Support HDMI audio output, backlight brightness adjustable
Product Parameters
| SKU | MPI4008 |
| Screen Size | 4.0inch |
| LCD Type | TFT |
| Module Interface | HDMI |
| Resolution | 800*480 (Pixel) |
| Touch Screen Controller | XPT2046 |
| LCD Driver IC | NT35510 |
| Backlight | LED |
| power consumption | 0.16A*5V |
| Working temperature（℃） | -20~70 |
| Module PCB Size | 98.60*58.05 (mm) |
| Package Size | 143*134*51 (mm) |
| Product Weight(g) | 125 (g) |
Hardware Description
- ① 3.5mm Headphone Jack: Output audio signal
- ② HDMI：Used to connect the main board and LCD display for HDMI transmission
- ③ Micro USB：Get 5V Power from USB, If ⑤-13*2 Pin Socket has been connected, that this USB interface can be No Connect.
- ④ Backlight adjustment button: Short press backlight change 10%, long press a few seconds to close backlight; short press to open backlight
- ⑤ 13*2 Pin Socket：Get +5V Power from raspberry Pi to LCD, at the same time transfer touch signal back to Raspberry Pi.
- 13*2 Pin Socket interface definition:
| Pin | Name | Description |
| 1、17 | 3.3V | Power supply +3.3V |
| 2、4 | 5V | Power supply +5V |
| 3、5、7、8、10、11、12、13、15、16、18、24 | NC | NC |
| 6、9、14、20、25 | GND | GND |
| 19 | TP_SI | SPI data input of touch panel |
| 21 | TP_SO | SPI data output of touch panel |
| 22 | TP_IRQ | The touch panel is interrupted and the low level is detected when the touch panel is pressed down |
| 23 | TP_SCK | Touch the SPI clock signal of the panel |
| 26 | TP_CS | Touch panel select signal, low level select touch panel |
- Dimension drawing
How to use Raspbian/Ubuntu Mate/Kali/Retropie system
Method 1
1) Download the driver image file from the website:
http://www.lcdwiki.com/4inch_HDMI_Display-C#Download_Resources
2) Format Micro SD card by SDFormatter
3) Burn the official image into Micro SD card by using Win32DiskImager.
4) Insert Micro SD card, connect LCD, start Raspberry Pi, and it will work normally.
Method 2
- Step 1, install the latest official images of various systems (Q:Don‘t know how to install？)
- Step 2,Connect to Raspberry Pi
- As shown in the figure, connect the LCD module to the Raspberry Pi
- Step 3, Install the LCD driver
- A. Install drivers in the Raspbian system(Raspberry Pi requires Internet connection)
- (1)Log on to the Raspberry Pi terminal(User: pi; Password: raspberry) (Q:SSH cannot connect？)
- (2)Execute the following command (copy and paste it by right-clicking on the Putty window):
sudo rm -rf LCD-show git clone https://github.com/goodtft/LCD-show.git chmod -R 755 LCD-show cd LCD-show/ sudo ./MPI4008-show |
- B. Install drivers in the Ubuntu / Kali / RetroPie system
- (1)Download local drivers "LCD-show.tar.gz"
- (2)Copy "LCD-show.tar.gz" to the root directory of Micro SD card of Raspberry Pi system （After step 1, copy the "LCD-show.tar.gz" into the Micro SD card root directory）
- (3)Log on to the Raspberry Pi terminal, Execute the following command
- B. Install drivers in the Ubuntu / Kali / RetroPie system
cd /boot tar -xvzf LCD-show.tar.gz chmod -R 755 LCD-show cd LCD-show/ sudo ./MPI4008-show |
- Step 4, Check whether the driver is installed successfully
- After the installation of the LCD driver is completed, the system will restart automatically. If the LCD can be normally displayed and touched, the installation of the driver is successful
注意事项：
- A、Ubuntu系统默认SSH没有开启，具体开启方法见RaspberryPi Ubuntu-mate系统开启SSH说明
- B、Ubuntu-18.04系统ssh连接可能会失败，具体解决方法见RaspberryPi Ubuntu-mate-18.04系统ssh连接失败解决方法说明
- C、RetroPie-rpi1_zero系统不能通过SSH登录（没有网口和wifi模块），需要通过串口拷贝驱动，具体设置方法见RaspberryPi Zero打开串口说明
- D、Retropie系统游戏安装及设置说明见RaspberryPi Retropie系统使用说明
How to use as PC Monitor
- Connected the computer HDMI output to the LCD HDMI interface by HDMI cable.
- Power to Micro USB interface
- If you have multiple monitors, please pull the other displayer, and make this LCD as the only displayer for testing.
- As computer monitors, the touch function will not be available.
Download resources
- Documents
- How_to_install_the_LCD_driver_V1.2
- How_to_install_matchbox-keyboard
- How_to_calibrate_the_resistance_touch_screen-V1.2
- How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf
- How_to_change_display_direction-GPIO-Resistive_Touch-V1.2
- Driver Download
- Image Download
- If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,
- Please Try our Configned images for tested.
- Just need download and write the image into the Micro SD card. DO NOT need any driver installation steps.
| Image Name | Version | Support | Password | Download | |
|---|---|---|---|---|---|
| Raspbian | 20190408 | PI3B+/A/A+/B/B+/PI2/
PI3/ZERO/ZERO W |
user:pi
password:raspberry |
 360Yun:
|
MPI4008-4inch-HDMI-C-Raspbian-20190408.7z |
 Mega:
|
MPI4008-4inch-HDMI-C-Raspbian-20190408.7z | ||||
| Ubuntu | 18.04.02 | PI3B+,PI3B,PI2B | user:pi
password:raspberry |
360Yun:
|
MPI4008-4inch-HDMI-C-Ubuntu-18.04.02.7z |
| Mega:
|
MPI4008-4inch-HDMI-C-Ubuntu-18.04.2.7z | ||||
| Kali-linux | 2019.1 | PI3B+,PI3,PI2 | user:root
password:toor |
360Yun:
|
MPI4008-4inch-HDMI-C-Kali-2019.1.7z |
| Mega:
|
MPI4008-4inch-HDMI-C-Kali-2019.1.7z | ||||
| RetroPie | 4.4 | Pi1,Pi-ZERO | user:pi
password:raspberry |
360Yun:
|
MPI4008-4inch-HDMI-C-retropie-4.4-rpi1-zero.7z |
| Mega:
|
MPI4008-4inch-HDMI-C-retropie-4.4-rpi1-zero.7z | ||||
| RetroPie | 4.4 | Pi3B+,Pi3,Pi2 | user:pi
password:raspberry |
360Yun:
|
MPI4008-4inch-HDMI-C-retropie-4.4-rpi2-rpi3.7z |
| Mega:
|
MPI4008-4inch-HDMI-C-retropie-4.4-rpi2-rpi3.7z | ||||
- MD5 of Image
- Common Software
